How to use a Rockwell Hardness Tester for comparative hardness testing?

May 27, 2025Leave a message

Hey there! I'm from a Rockwell hardness tester supply company, and I'm super stoked to share with you how to use a Rockwell hardness tester for comparative hardness testing. It's a nifty tool that can give you a lot of insights into the materials you're working with.

First off, let's get a bit of background. The Rockwell hardness test is a widely used method to measure the hardness of materials. It works by indenting the material with a specific indenter under a certain load. The depth of the indentation is then measured, and this measurement is used to determine the hardness value on the Rockwell scale.

HBRV-187.5 Brinell Rockwell Vickers Hardness TesterHR-150B Higher Rockwell Hardness Tester

Getting Ready for the Test

Before you start testing, you need to make sure you've got everything set up right. First, choose the right indenter and load for the material you're testing. Different materials require different combinations of indenters and loads. For example, harder materials might need a diamond cone indenter with a higher load, while softer materials could use a ball indenter with a lower load.

Next, prepare your test specimen. It should be clean and flat. Any dirt, oil, or unevenness on the surface can affect the test results. You can use a fine-grit sandpaper to smooth the surface if needed. Make sure the specimen is thick enough so that the indentation doesn't go through to the other side. A good rule of thumb is that the specimen should be at least 10 times the depth of the indentation.

Setting Up the Rockwell Hardness Tester

Now, let's set up the tester. First, turn on the machine and let it warm up for a few minutes. This helps to ensure accurate readings. Then, select the appropriate scale on the tester. The most common scales are the A, B, and C scales. The A scale is used for very hard materials like carbides, the B scale for softer metals like aluminum, and the C scale for medium to hard steels.

Once you've selected the scale, place the indenter in the tester. Make sure it's properly seated and tightened. Then, adjust the anvil so that it's level and in the right position. You can use the leveling screws on the base of the tester to do this.

Performing the Test

Now it's time to do the actual test. Place your prepared specimen on the anvil. Make sure it's centered under the indenter. Then, lower the indenter slowly onto the specimen until it just touches the surface. You can use the handwheel on the tester to do this.

Once the indenter is touching the surface, apply the minor load. This is usually around 10 kgf. The tester will automatically measure the initial depth of the indentation. Then, apply the major load. The major load depends on the scale you've selected. For example, on the C scale, the major load is 150 kgf.

Keep the major load applied for a specified time, usually around 15 seconds. This allows the indentation to fully develop. After the specified time, remove the major load, but keep the minor load applied. The tester will then measure the final depth of the indentation.

Reading the Results

The difference between the initial and final depths of the indentation is used to calculate the Rockwell hardness value. The tester will usually display this value on a digital screen or a dial. Make a note of this value.

To do comparative hardness testing, you'll need to test multiple specimens. For example, if you're comparing the hardness of different types of steel, you'll need to test each type of steel using the same indenter, load, and scale. Then, compare the Rockwell hardness values of each specimen. The higher the Rockwell hardness value, the harder the material.

Tips for Accurate Testing

  • Repeat the test: To ensure accuracy, it's a good idea to repeat the test on the same specimen at least three times. Take the average of the results to get a more reliable hardness value.
  • Avoid testing near edges or holes: Testing near edges or holes can give inaccurate results because the material around these areas may be stressed or have a different microstructure.
  • Keep the tester clean: Regularly clean the indenter and anvil to prevent dirt and debris from affecting the test results.

Our Rockwell Hardness Testers

At our company, we offer a range of high-quality Rockwell hardness testers. If you're interested in learning more about our products, check out the following links:

Conclusion

Using a Rockwell hardness tester for comparative hardness testing is a great way to understand the properties of different materials. By following the steps outlined in this blog, you can ensure accurate and reliable test results. If you're in the market for a Rockwell hardness tester, we'd love to hear from you. Contact us to discuss your specific needs and let's start a great business relationship!

References

  • ASTM E18 - Standard Test Methods for Rockwell Hardness of Metallic Materials
  • ISO 6508 - Metallic materials -- Rockwell hardness test